| |
|
|
|
|
|
|
| |
|
| |
 |
|
| |
|
|
| |
|
The Journal of Mechanical Science and Technology, Volume 26, Number 4, 2012 |
|
|
Nonlinear vibration and rippling instability for embedded carbon nanotubes
Payam Soltani*, D. D. Ganji, I. Mehdipour and A. Farshidianfar
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.985-992, 2012 |
|
|
Direct identification of non-proportional modal damping matrix for lumped mass system using modal parameters
Cheonhong Min, Hanil Park* and Sooyong Park
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.993-1002, 2012 |
|
|
Interior noise analysis of a construction equipment cabin based on airborne and structure-borne noise predictions
Sung-Hee Kim, Suk-Yoon Hong*, Jee-Hun Song and Won-Ho Joo
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1003-1009, 2012 |
|
|
Free vibration analysis of a hermetic capsule by pseudospectral method
Jinhee Lee*
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1011-1015, 2012 |
|
|
Anti-plane moving crack in a functionally graded piezoelectric layer between two dissimilar piezoelectric strips
Jeong Woo Shin and Young-Shin Lee*
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1017-1025, 2012 |
|
|
Numerical simulation of flow past rectangular cylinders with different aspect ratios using the incompressible lattice Boltzmann method
S. Ul Islam, C. Y. Zhou*, A. Shah and P. Xie
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1027-1041, 2012 |
|
|
Numerical simulation of rotordynamic coefficients for eccentric annular-type-plain-pump seal using CFD analysis
Tae Woong Ha* and Bok Seong Choe
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1043-1048, 2012 |
|
|
Laser velocimetry of a plane mixing layer with a specific initial condition for study of turbulence characteristics of enhanced growth rate
Mojtaba Mehrjooei, Nader Montazerin* and Abraham Damangir
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1049-1057, 2012 |
|
|
Quantitative analysis of a two-dimensional ice accretion on airfoils
Chankyu Son, Sejong Oh and Kwanjung Yee*
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1059-1071, 2012 |
|
|
A study to maximize the crash energy absorption efficiency within the limits of crash space
Bae-Young Kim, Choong-Min Jeong, Si-Woo Kim and Myung-Won Suh*
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1073-1078, 2012 |
|
|
Damage detection by the distribution of predicted constraint forces
Salam Rahmatalla, Eun-Taik Lee and Hee-Chang Eun*
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1079-1087, 2012 |
|
|
Predictive carbon nanotube models using the eigenvector dimension reduction (EDR) method
Zhimin Xi and Byeng D. Youn*
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1089-1097, 2012 |
|
|
Coupled linkage system optimization for minimum power consumption
Kihan Shin, Sungcheul Lee, Hyunpyo Shin*, Youngsun Yoo and Jongwon Kim
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1099-1106, 2012 |
|
|
Improvement of the performance of a tetrahedral element with rotational DOFs using strain smoothing techniques
Chang Min Shin*, Seung Han Kang and Byung Chai Lee
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1107-1114, 2012 |
|
|
Efficient frequency response and its direct sensitivity analyses for large-size finite element models using Krylov subspace-based model order reduction
Jeong Sam Han*
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1115-1126, 2012 |
|
|
Non-linear analysis of skew thin plate by finite difference method
Chi-Kyung Kim* and Myung-Hwan Hwang
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1127-1132, 2012 |
|
|
Prediction of warpage in plastic injection molding based on design of experiments
Wei Guo*, Lin Hua, Huajie Mao and Zhenghua Meng
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1133-1139, 2012 |
|
|
Optimization of squeeze casting parameters for non symmetrical AC2A aluminium alloy castings through Taguchi method
P. Senthil* and K. S. Amirthagadeswaran
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1141-1147, 2012 |
|
|
Robust sliding mode control for uncertain servo system using friction observer and recurrent fuzzy neural networks
Seong Ik Han, Chan Se Jeong and Soon Yong Yang*
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1149-1159, 2012 |
|
|
Modeling of an air motor servo system and robust sliding mode controller design
Chia-Hua Lu* and Yean-Ren Hwang
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1161-1169, 2012 |
|
|
Design and simulation for a hydraulic actuated quadruped robot
Xuewen Rong, Yibin Li*, Jiuhong Ruan and Bin Li
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1171-1177, 2012 |
|
|
Neuro-fuzzy control strategy for an offshore steel jacket platform subjected to wave-induced forces using magnetorheological dampers
Atabak Sarrafan*, Seiyed Hamid Zareh, Amir Ali Akbar Khayyat and Abolghassem Zabihollah
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1179-1196, 2012 |
|
|
Collision detection and reaction on 7 DOF service robot arm using residual observer
Chang-Nho Cho, Joon-Hong Kim, Sang-Duck Lee and Jae-Bok Song*
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1197-1203, 2012 |
|
|
Improvement and experimental validation of a multi-zone model for combustion and NO emissions in CNG fueled spark ignition engine
Omid Asgari*, Siamak Kazemzadeh Hannani and Reza Ebrahimi
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1205-1212, 2012 |
|
|
Numerical simulation of the effects of a suction line heat exchanger on vapor compression refrigeration cycle performance
Ji Hwan Jeong*, Sang-Goo Park, Debasish Sarker and Keun Sun Chang
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1213-1226, 2012 |
|
|
An experimental study on the transition criteria of open channel natural convection flows
Bong-Jin Ko, Min-Hwan Kim and Bum-Jin Chung*
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1227-1234, 2012 |
|
|
Analysis of the combustion oscillation in a silo-type gas turbine combustor and its suppression
Seok Bin Seo, Dal Hong Ahn, Jong Ho Park and Dong Jin Cha*
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1235-1240, 2012 |
|
|
Performance and emission characteristics of a low heat rejection spark ignited engine fuelled with E20
C. Ramesh Kumar* and G. Nagarajan
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1241-1250, 2012 |
|
|
Study of the regenerator constituting material influence on a gamma type Stirling engine
Ramla Gheith, Fethi Aloui* and Sassi Ben Nasrallah
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1251-1255, 2012 |
|
|
A numerica1 study of fluid flow and heat transfer in different microchannel heat sinks for electronic chip cooling
Shanglong Xu*, Guangxin Hu, Jie Qin and Yue Yang
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1257-1263, 2012 |
|
|
Experimental analysis of emission reduction by the split injection strategy using close post injection with a double-row nozzle in heavy EGR conditions
Jeongwoo Lee, Seungmok Choi, Seunghyup Shin, Hoimyung Choi and Kyoungdoug Min*
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1265-1274, 2012 |
|
|
Dynamic behavior of flexible sensory hair in an oscillating flow
Byung Kyu Park* and Joon Sik Lee
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1275-1282, 2012 |
|
|
Efficiency analysis of straight fin with variable heat transfer coefficient and thermal conductivity
Somayyeh Sadri*, Mohammad Reza Raveshi and Shayan Amiri
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1283-1290, 2012 |
|
|
Forced convection heat transfer of steam in a square ribbed channel
Jiazeng Liu, Jianmin Gao and Tieyu Gao*
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1291-1298, 2012 |
|
|
Evaluation of a hot oil immersion drying method for the upgrading of crushed low-rank coal
Tae-In Ohm*, Jong-Seong Chae, Jae-Ho Lim and Sung-Hyun Moon
The Journal of Mechanical Science and Technology, vol. 26, no. 4, pp.1299-1303, 2012 |
|
|
|
|
 |
|
|
|
|
| |
| |
| |
|
|
| |
|
JMST Editorial Office: #702 KSTC New Bldg, 22 7-gil, Teheran-ro, Gangnam-gu, Seoul 06130, Korea
TEL: +82-2-501-3605, E-mail: editorial@j-mst.org |
JMST Production Office: #702 KSTC New Bldg, 22 7-gil, Teheran-ro, Gangnam-gu, Seoul 06130, Korea
TEL: +82-2-501-6056, FAX: +82-2-501-3649, E-mail: editorial@j-mst.org |
|
| |
|
|
